| Questions and Answers |
| Q: |
Hi there...how much will a frame for a 09 ford f150 be..I wana be able to tuck 24x14 in the rear n 24x10 in front..let me know a good prize thaxx |
| A: |
All my frames for 1/2 ton or lighter are $5495.00 thats the frame seen on here with prebent rails |
| A: |
The price listed is for any 1/2 ton or smaller truck with all the suspension.If you look at our website you will see under products that we have options too for your chassis as well. One option if you not interested in air ride is that we can substitute the bags and shocks for coil over as well. |
| Q: |
I have a bagged 04 silverado 1500 single cab v6 5-speed & i have been talking back and fourth with the choppin block in fresno and method motor werks, to build a custom frame for me using the stock 04 front clip. They say i can lay rocker on 24"s with one of there frames using my stock arms (properly clearanced) and 2" drop spindles, is this possible from you guys? or would you reccomend one of your IFS packages? Pros & cons? What about lift? I am looking for as much as possible. im looking to do a wish bone rear 4- link, with bags on the lower bars mounted mid way for 15-20" of travel out of slam re 7s or 8s if theres room. I dont need drilled and slotted rotors or anything fancy. I have disk all the way around with a 10 bolt rear. If you set up the chassis i can install the controll arms rear axle ect. I have been interested in doing this for 6 months now but i have some strength concerns, and i dont want to invest 7500$ in a piece of junk that will leave me stranded. |
| A: |
I totally understand what you are talking about on the strengths. I have been building chassis for almost 10 years on and off and more on the last 6 years than off. Our design is one that gives you added strengths where it is most needed. For the price advertised you would get a frame to lay 24"s with rockers on the ground. 10.5 lift in the front with 3 degrees of camber gain, 1/2 inch caster, 5deg anti dive and 1/8 total of bump steer. We have been R & D this for quite some years to get the max out of the front suspension. Now on the rear we have a parallel four link with bag on lower bar that add tremendous ride quility with great lift, we have maxed it out a 16" of travel and that is without shocks on it. We could go more but then we have issues with the bag spreading wider on one side ( I dont like that personally). I would rather give you something I am sure of on the front suspension than trying to reuse your stuff and having to modify it. I do believe that you will like ours better and the quality is unmatched. I can say that proudly. |
| Q: |
Could you make a sfbd front subframe for a astrovan to lay on 22" wheels. If so what would be the cost? |
| A: |
Yes and your looking at 3400.00 |
| Q: |
ok well i had it bodydropt 6" b4, and i just wasnt happy with how it rode, so i decied to redo everything on it..... if i can have someone build a frame and keep the monkey off my back on that aspect then more power to me...
id like for u to just take care of all the suspension, brake and steering compomets.....and if i did a rear end, would i need to get u mine or can u get ahold of a case?
and i plan on do a whole front end conversion, and doing some work to squeeze those 4s....
|
| A: |
Ok I am assuming that you will install the body and motor correct. Now will you be using the bd cab or a new one? I would be honored to be able to help you in that build. Now we offer a new 9" housing for extra. If you look at our website you will see the extras we offer. We also can do the sheetmetal conversion if you need some help. But the price for what you are looking for on the chassis is 5595.00. |
| Q: |
What kinda problems would I have?? I've seen some s10 with 24s...and would I be able to do a 22/24 combo on that and ya if u can gimme a price range |
| A: |
Ok well if we can go with the smallest 24 wheel tire combo I believe yes we might be able to do it. Also the 22 -24 combo we can do easier. The price on the chassis is the price listed. What all would you need to have if you wanted to do a drive in drive out? Do you have air ride? Thats something i will need to have to give you a good estimate. |
| Q: |
that's cool man, i understand where your coming from, how much for a sfbd chassis for a 96 ranger? |
| A: |
5179.97 for the ranger with out a rear end assy. now we do have other options too like brake lines, fuel lines, etc.. |
| Q: |
86 s-10 pickup w/ 20's......how much? |
| A: |
5179.97 now after the sale. |
| Q: |
i'm not trying to be an ass, just a serious question, barely legal can build one and send it to my door for around 2000, why would i spend 2000 grand more? their average price is about 2500 for a sfbd chassis |
| A: |
That's fine you do get what you pay for. Barely legal is i guess having issues with getting parts out. I can do a parameter frame that what our other chassis classes are for. If you look at our website you will see different class of chassis then one of them might work for you. But I do have the most complete frame that you can buy for that money. Plus I have around 12 on order so I must be doing something right! |
| Q: |
i have a 92 caprice wantin to bag what i needa do and how much |
| A: |
Caprices are a little easier on wheels up to 18's if you want bigger we can do that for you also. Most of the problem is the rear link setup from the factory. We can install one for you that will suit your needs. To do this job for up to 18's your looking about 3500.00 for a great setup. 20's your looking at about 4300.00 Let me know if you need anything else. |
| Q: |
95 GMC sonoma, Extended Cab 3rd Door, STOCK FLOOR, 22" rims, how much would this frame cost? Does it come with control arms,calapiers, everything needed to use most of the stock parts right back on the frame? |
| A: |
Oh and to mention our frames will tuck a 24 inch wheel if needed. |
| Q: |
95 GMC sonoma, Extended Cab 3rd Door, STOCK FLOOR, 22" rims, how much would this frame cost? Does it come with control arms,calapiers, everything needed to use most of the stock parts right back on the frame? |
| A: |
This frame comes with all new front suspension, front brakes, and steering. Plus four 2600 bags, fuel cell and four link. Plus has universal body mounts for your truck all for 4143.98. That is until march 30th that is when our sale ends. |
| Q: |
can you build one for a 91 mighty max? |
| A: |
Yes we can that is no problem
|
| Q: |
can you build one for a 91 mighty max? |
| A: |
Yes we can that is no problem
|
| Q: |
What about the fuel cell? |
| A: |
No iam sorry the stage 3 doesnt come with a fuel cell. |
| Q: |
Does the stage three frames come with the mustang 2 drop spindles? |
| A: |
Yes it does come with the spindles. I noticed a problem on the website but no have changed it. This comes with the rails, front steering, suspension, rear four link, What it doesnt come with is the four bags, hubs, calipers or caliper brackets. |
| Q: |
In the picture of the rear link what brand is the lower arms with the bags mounted to. only reason i ask is my truck has them some ones and i would really like to know the brand, any info since i need a few replacment parts. thanks |
| A: |
All parts on these chassis are all out parts either we manufacturer or have manufactured for us. Everything is designed in house by us. |
| Q: |
how exactly does this work??? gotta 93 s10 blazer 4 door |
| A: |
Well what you would do is order your frame for your truck with the wheels & tire combo you want to run. We even will build the frame for coil overs and not just air ride. When you order your chassis you will be given options for just the chassis build and then options for finishing, ie brake lines rearend assy, etc.. We require 75% down then the other 25 upon shipment or pickup. Turnaround is usually 4-6 weeks from schedualed date. |
| Q: |
Ihave a 1962 suburban carryall which I am looking to get a rolling chasis built for. is this somethung you can do? if so do you need the truck? please let me know. thanks. the burban can be viewed on mautofied by looking up suburban-carryall |
| A: |
Due to the year yes we would need the body for chassis specs. Yes we can build you one for your truck that is not a problem |
| Q: |
CAN YOU BUILD THAT TO FIT A COLORADO? IF SO WHAT KIND OF SPINDLES DO YOU USE? |
| A: |
Yes we can build it for your colorado. No problem! We use mustang II spindles that allow us to tuck upto a 24" wheel and tire combo. |
Back to Search Results
Print
Email
Save this Listing
report abuse
Loading ...